American Dryer Corp. ML-96D Uživatelský manuál

ADC Part No. 113125For replacement parts, contact the reseller from which the dryerwas purchased orAmerican Dryer Corporation88 Currant RoadFall River

6SECTION IISPECIFICATIONS/COMPONENT IDENTIFICATIONA. SPECIFICATIONSIMPORTANT: Dryer must be supplied with clean, dry, and regulated air pressure at 8

7NOTE: ADC reserves the right to make changes in specifications at any time without notice orobligation.SpecificationsML-96D

8B. COMPONENT IDENTIFICATION1. Dryer Front ViewIllus. No. Description1 Microprocessor Control/Keyboard (touch pad) Panel Assembly (controls)2 Control

9Illus. No. Description1 Electrical Service Connections2 Top Console3 Heating Unit4 Relay/Wiring Box5 Data Label and Installation Label6 Air Connectio

10SECTION IIIINSTALLATION PROCEDURESInstallation should be performed by competent technicians in accordance with local and state codes. In theabsence

11B. UNPACKING/SETTING UPRemove protective shipping material (i.e., plastic wrap and optional shipping box) from dryer.IMPORTANT: Dryer must be trans

121. Leveling DryerTo level dryer, place 4-inch (10.16 cm) square metal shims (refer to the illustration on page 11) or othersuitable material under t

13C. DRYER ENCLOSURE REQUIREMENTSEven though a 30-inch (76.2 cm) clearance is acceptable, it is recommended that the rear of the dryer bepositioned

14D. FRESH AIR SUPPLYWhen the dryer is operating, it draws in room air, heats it, passes this air through the basket (tumbler), andexhausts it out of

15E. EXHAUST REQUIREMENTS1. General Exhaust Ductwork InformationExhaust ductwork should be designed and installed by a qualified professional. Impro

Retain This Manual In A Safe Place For Future ReferenceAmerican Dryer Corporation products embody advanced concepts in engineering, design, and safety

162. Single Dryer VentingWhere possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust duct shouldbe laid out in suc

17IMPORTANT: For extended ductwork runs, the cross section area of the ductwork can only beincreased to an extent. Maximum proportional ductwork runs

183. Multiple Dryer (common) VentingIf it is not feasible to provide separate exhaust ducts for each dryer, ducts from individual dryers may bechannel

19a. Outside Ductwork Protection1) To protect the outside end of horizontal ductwork from the weather, a 90º elbow bent downwardshould be installed wh

20Each dryer should be connected to an independently protected branch circuit. The dryer must be connectedwith copper wire only. DO NOT use aluminum

213. GroundingA ground (earth) connection must be provided and installed in accordance with state and local codes. Inthe absence of these codes, grou

22G. GAS INFORMATIONIt is your responsibility to have ALL plumbing connections made by a qualified professional to assure that the gasplumbing instal

232. Technical Gas Dataa. Gas Specificationsb. Gas ConnectionsInlet connection -----------1-inch N.P.T.Inlet supply size -----------1-inch N.P.T. (min

243. Piping and ConnectionsALL components/materials must conform to National Fuel Gas Code Specifications ANSI Z223.1-LATESTEDITION, or in Canada, CAN

25Consistent gas pressure is essential at ALL gas connections. It is recommended that a 1-inch (2.54 cm)pipe gas loop be installed in the supply line

IMPORTANTYOU MUST DISCONNECT and LOCKOUT THE ELECTRIC SUPPLY and THE GASSUPPLY BEFORE ANY COVERS or GUARDS ARE REMOVED FROM THE MACHINETO ALLOW ACCESS

266. Be sure ALL side and base panels are on the dryer.7. Check ALL service doors to insure that they are closed and secure.8. Be sure the lint drawer

273) Once ignition is established, a gas pressure test should be taken at the gas valve pressure tap ofeach dryer to assure that the water column (W.C

28NOTE: The dryer can be stopped at any time by opening main door or by pressing the "STOP" key.To restart the dryer, press the "START&

29SECTION IVSERVICE/PARTS INFORMATIONA. SERVICE1. Service must be performed by a qualified trained technician, service agency, or gas supplier. If s

30SECTION VWARRANTY INFORMATIONA. RETURNING WARRANTY CARD(S)1. Before any dryer leaves the ADC factory test area, a warranty card is placed on the ba

312. Each part must be tagged with the following information:a. Model number and serial number of the dryer from which part was removed.b. Nature of f

32SECTION VIROUTINE MAINTENANCEA. CLEANINGA program or schedule should be established for periodic inspection, cleaning, and removal of lint from var

332. Remove lint from gas valve burner area with a dusting brush or vacuum cleaner attachment.3. Clean any lint accumulation in and around both the bl

34SECTION VIIPROCEDURE FOR FUNCTIONAL CHECKOF REPLACEMENT COMPONENTS1. For Models With Johnson Controls Direct Spark Ignition (DSI) Module (G760)Theor

352. For Direct Spark Ignition (DSI) System Models Manufactured With ADC Module Part No. 880815a. Upon completing installation of thereplacement DSI m

WARNINGThe dryer must never be operated with any of the back guards, outer tops, or servicepanels removed. PERSONAL INJURY or FIRE COULD RESULT.IMPOR

36SECTION VIIIDATA LABEL/LOCATION INFORMATIONA. DATA LABELContact American Dryer CorporationWhen contacting American Dryer Corporation certain infor

37THE DATA LABEL1. MODEL NUMBERThe model number is an ADC number, which describes the size of the dryer and thetype of heat (gas, electric, or steam).

38SECTION IXBURNER and BASKET (TUMBLER)/LINT CHAMBERMANUAL RESET HI-LIMIT INSTRUCTIONS(FOR PHASE 6 MODELS)This dryer was manufactured with a burner ma

ADC 113125 1- 02/16/00-10 2- 12/08/00-10 3*03/09/01-25

Table of ContentsSECTION IIMPORTANT INFORMATION...3A. Receiving and Handli

SECTION VIIPROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENTCOMPONENTS ...

3SECTION IIMPORTANT INFORMATIONA. RECEIVING and HANDLINGThe dryer is shipped in a protective stretch wrap cover with protective cardboard corners and

4B. SAFETY PRECAUTIONS WARNING: For your safety, the information in this manual must be followed to minimize the risk offire or explosion or to preve

57. A program should be established for the inspection and cleaning of lint in the heating unit area, exhaustductwork, and inside the dryer. The freq